Filtered by vendor Juniper
Subscribe
Total
320 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2021-0259 | 1 Juniper | 9 Junos, Junos Os Evolved, Qfx5100 and 6 more | 2023-12-10 | 3.3 LOW | 7.4 HIGH |
| Due to a vulnerability in DDoS protection in Juniper Networks Junos OS and Junos OS Evolved on QFX5K Series switches in a VXLAN configuration, instability might be experienced in the underlay network as a consequence of exceeding the default ddos-protection aggregate threshold. If an attacker on a client device on the overlay network sends a high volume of specific, legitimate traffic in the overlay network, due to an improperly detected DDoS violation, the leaf might not process certain L2 traffic, sent by spines in the underlay network. Continued receipt and processing of the high volume traffic will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX5K Series: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. Juniper Networks Junos OS Evolved on QFX5220: All versions prior to 20.3R2-EVO. | |||||
| CVE-2021-0230 | 1 Juniper | 27 Junos, Srx100, Srx110 and 24 more | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3. | |||||
| CVE-2021-0255 | 1 Juniper | 1 Junos | 2023-12-10 | 7.2 HIGH | 7.8 HIGH |
| A local privilege escalation vulnerability in ethtraceroute of Juniper Networks Junos OS may allow a locally authenticated user with shell access to escalate privileges and write to the local filesystem as root. ethtraceroute is shipped with setuid permissions enabled and is owned by the root user, allowing local users to run ethtraceroute with root privileges. This issue affects Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D240; 17.3 versions prior to 17.3R3-S11, 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1. | |||||
| CVE-2021-0252 | 1 Juniper | 4 Junos, Nfx150, Nfx250 and 1 more | 2023-12-10 | 4.6 MEDIUM | 7.8 HIGH |
| NFX Series devices using Juniper Networks Junos OS are susceptible to a local code execution vulnerability thereby allowing an attacker to elevate their privileges via the Junos Device Management Daemon (JDMD) process. This issue affects Juniper Networks Junos OS on NFX Series: 18.1 version 18.1R1 and later versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S5, 19.2R2. This issue does not affect: Juniper Networks Junos OS versions prior to 18.1R1. This issue does not affect the JDMD as used by Junos Node Slicing such as External Servers use in conjunction with Junos Node Slicing and In-Chassis Junos Node Slicing on MX480, MX960, MX2008, MX2010, MX2020. | |||||
| CVE-2021-0227 | 1 Juniper | 22 Junos, Srx100, Srx110 and 19 more | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| An improper restriction of operations within the bounds of a memory buffer vulnerability in Juniper Networks Junos OS J-Web on SRX Series devices allows an attacker to cause Denial of Service (DoS) by sending certain crafted HTTP packets. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. When this issue occurs, web-management, NTP daemon (ntpd) and Layer 2 Control Protocol process (L2CPD) daemons might crash. This issue affects Juniper Networks Junos OS on SRX Series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2; | |||||
| CVE-2021-0226 | 1 Juniper | 1 Junos Os Evolved | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| On Juniper Networks Junos OS Evolved devices, receipt of a specific IPv6 packet may cause an established IPv6 BGP session to terminate, creating a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue does not affect IPv4 BGP sessions. This issue affects IBGP or EBGP peer sessions with IPv6. This issue affects: Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S3-EVO; 20.2 versions prior to 20.2R2-S1-EVO; 20.3 versions prior to 20.3R2-EVO. This issue does not affect Juniper Networks Junos OS releases. | |||||
| CVE-2021-0282 | 1 Juniper | 1 Junos | 2023-12-10 | 7.1 HIGH | 7.5 HIGH |
| On Juniper Networks Junos OS devices with Multipath or add-path feature enabled, processing a specific BGP UPDATE can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued receipt and processing of this UPDATE message will create a sustained Denial of Service (DoS) condition. This BGP UPDATE message can propagate to other BGP peers with vulnerable Junos versions on which Multipath or add-path feature is enabled, and cause RPD to crash and restart. This issue affects both IBGP and EBGP deployments in IPv4 or IPv6 network. Junos OS devices that do not have the BGP Multipath or add-path feature enabled are not affected by this issue. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S18; 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S3; | |||||
| CVE-2021-0251 | 1 Juniper | 17 Junos, Mx10, Mx10003 and 14 more | 2023-12-10 | 5.0 MEDIUM | 8.6 HIGH |
| A NULL Pointer Dereference vulnerability in the Captive Portal Content Delivery (CPCD) services daemon (cpcd) of Juniper Networks Junos OS on MX Series with MS-PIC, MS-SPC3, MS-MIC or MS-MPC allows an attacker to send malformed HTTP packets to the device thereby causing a Denial of Service (DoS), crashing the Multiservices PIC Management Daemon (mspmand) process thereby denying users the ability to login, while concurrently impacting other mspmand services and traffic through the device. Continued receipt and processing of these malformed packets will create a sustained Denial of Service (DoS) condition. While the Services PIC is restarting, all PIC services will be bypassed until the Services PIC completes its boot process. An attacker sending these malformed HTTP packets to the device who is not part of the Captive Portal experience is not able to exploit this issue. This issue is not applicable to MX RE-based CPCD platforms. This issue affects: Juniper Networks Junos OS on MX Series 17.3 version 17.3R1 and later versions prior to 17.4 versions 17.4R2-S9, 17.4R3-S2; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect: Juniper Networks Junos OS versions prior to 17.3R1. | |||||
| CVE-2021-0253 | 1 Juniper | 4 Junos, Nfx150, Nfx250 and 1 more | 2023-12-10 | 4.6 MEDIUM | 7.8 HIGH |
| NFX Series devices using Juniper Networks Junos OS are susceptible to a local command execution vulnerability thereby allowing an attacker to elevate their privileges via the Junos Device Management Daemon (JDMD) process. This issue affects Juniper Networks Junos OS on NFX Series 17.2 version 17.2R1 and later versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S5, 18.4R3-S5; 19.1 versions prior to 19.1R1-S3; 19.2 version 19.1R2 and later versions prior to 19.2R3; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2-S2. 19.4 versions 19.4R3 and above. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R1. This issue does not affect the JDMD as used by Junos Node Slicing such as External Servers use in conjunction with Junos Node Slicing and In-Chassis Junos Node Slicing on MX480, MX960, MX2008, MX2010, MX2020. | |||||
| CVE-2021-0269 | 1 Juniper | 1 Junos | 2023-12-10 | 5.1 MEDIUM | 8.8 HIGH |
| The improper handling of client-side parameters in J-Web of Juniper Networks Junos OS allows an attacker to perform a number of different malicious actions against a target device when a user is authenticated to J-Web. An attacker may be able to supersede existing parameters, including hardcoded parameters within the HTTP/S session, access and exploit variables, bypass web application firewall rules or input validation mechanisms, and otherwise alter and modify J-Web's normal behavior. An attacker may be able to transition victims to malicious web services, or exfiltrate sensitive information from otherwise secure web forms. This issue affects: Juniper Networks Junos OS: All versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2. | |||||
| CVE-2021-0233 | 1 Juniper | 3 Acx4000, Acx500, Junos | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in Juniper Networks Junos OS ACX500 Series, ACX4000 Series, may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a Forwarding Engine Board (FFEB) crash. Continued receipt of these packets will sustain the Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX500 Series, ACX4000 Series: 17.4 versions prior to 17.4R3-S2. | |||||
| CVE-2021-0246 | 1 Juniper | 8 Junos, Srx1500, Srx4100 and 5 more | 2023-12-10 | 4.6 MEDIUM | 7.3 HIGH |
| On SRX1500, SRX4100, SRX4200, SRX4600, SRX5000 Series with SPC2/SPC3, devices using tenant services on Juniper Networks Junos OS, due to incorrect default permissions assigned to tenant system administrators a tenant system administrator may inadvertently send their network traffic to one or more tenants while concurrently modifying the overall device system traffic management, affecting all tenants and the service provider. Further, a tenant may inadvertently receive traffic from another tenant. This issue affects: Juniper Networks Junos OS 18.3 version 18.3R1 and later versions on SRX1500, SRX4100, SRX4200, SRX4600, SRX5000 Series with SPC2; 18.3 versions prior to 18.3R3 on SRX1500, SRX4100, SRX4200, SRX4600, SRX5000 Series with SPC2; 18.4 versions prior to 18.4R2 on SRX1500, SRX4100, SRX4200, SRX4600, SRX5000 Series with SPC2/SPC3; 19.1 versions prior to 19.1R2 on SRX1500, SRX4100, SRX4200, SRX4600, SRX5000 Series with SPC2/SPC3. This issue does not affect: Juniper Networks Junos OS versions prior to 18.3R1. | |||||
| CVE-2021-0278 | 1 Juniper | 1 Junos | 2023-12-10 | 7.2 HIGH | 7.8 HIGH |
| An Improper Input Validation vulnerability in J-Web of Juniper Networks Junos OS allows a locally authenticated attacker to escalate their privileges to root over the target device. junos:18.3R3-S5 junos:18.4R3-S9 junos:19.1R3-S6 junos:19.3R2-S6 junos:19.3R3-S3 junos:19.4R1-S4 junos:19.4R3-S4 junos:20.1R2-S2 junos:20.1R3 junos:20.2R3-S1 junos:20.3X75-D20 junos:20.3X75-D30 junos:20.4R2-S1 junos:20.4R3 junos:21.1R1-S1 junos:21.1R2 junos:21.2R1 junos:21.3R1 This issue affects: Juniper Networks Junos OS 19.3 versions 19.3R1 and above prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.3R1. | |||||
| CVE-2021-0264 | 1 Juniper | 21 Junos, Junos Os Evolved, Mx10 and 18 more | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the processing of traffic matching a firewall filter containing a syslog action in Juniper Networks Junos OS on MX Series with MPC10/MPC11 cards installed, PTX10003 and PTX10008 Series devices, will cause the line card to crash and restart, creating a Denial of Service (DoS). Continued receipt and processing of packets matching the firewall filter can create a sustained Denial of Service (DoS) condition. When traffic hits the firewall filter, configured on lo0 or any physical interface on the line card, containing a term with a syslog action (e.g. 'term <name> then syslog'), the affected line card will crash and restart, impacting traffic processing through the ports of the line card. This issue only affects MX Series routers with MPC10 or MPC11 line cards, and PTX10003 or PTX10008 Series packet transport routers. No other platforms or models of line cards are affected by this issue. Note: This issue has also been identified and described in technical service bulletin TSB17931 (login required). This issue affects: Juniper Networks Junos OS on MX Series: 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved on PTX10003, PTX10008: All versions prior to 20.4R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 19.3R1. | |||||
| CVE-2021-0286 | 1 Juniper | 1 Junos Os Evolved | 2023-12-10 | 7.8 HIGH | 7.5 HIGH |
| A vulnerability in the handling of exceptional conditions in Juniper Networks Junos OS Evolved (EVO) allows an attacker to send specially crafted packets to the device, causing the Advanced Forwarding Toolkit manager (evo-aftmand-bt or evo-aftmand-zx) process to crash and restart, impacting all traffic going through the FPC, resulting in a Denial of Service (DoS). Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Following messages will be logged prior to the crash: Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:32710470974358 label:1089551617 for session:18 probe:35 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:19241453497049 label:1089551617 for session:18 probe:37 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:19241453497049 label:1089551617 for session:18 probe:44 Feb 2 10:14:39 fpc0 evo-aftmand-bt[16263]: [Error] Nexthop: Failed to get fwd nexthop for nexthop:32710470974358 label:1089551617 for session:18 probe:47 Feb 2 10:14:39 fpc0 audit[16263]: ANOM_ABEND auid=4294967295 uid=0 gid=0 ses=4294967295 pid=16263 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=11 Feb 2 10:14:39 fpc0 kernel: audit: type=1701 audit(1612260879.272:17): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=16263 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=1 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R2-EVO; 21.1 versions prior to 21.1R2-EVO. | |||||
| CVE-2020-1675 | 1 Juniper | 1 Mist Cloud Ui | 2023-12-10 | 4.3 MEDIUM | 8.3 HIGH |
| When Security Assertion Markup Language (SAML) authentication is enabled, Juniper Networks Mist Cloud UI might incorrectly process invalid authentication certificates which could allow a malicious network-based user to access unauthorized data. This issue affects all Juniper Networks Mist Cloud UI versions prior to September 2 2020. | |||||
| CVE-2020-1667 | 1 Juniper | 1 Junos | 2023-12-10 | 4.0 MEDIUM | 8.3 HIGH |
| When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process might be bypassed due to a race condition. Due to this vulnerability, mspmand process, responsible for managing "URL Filtering service", can crash, causing the Services PIC to restart. While the Services PIC is restarting, all PIC services including DNS filtering service (DNS sink holing) will be bypassed until the Services PIC completes its boot process. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R3; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3. This issue does not affect Juniper Networks Junos OS 17.4, 18.1, and 18.2. | |||||
| CVE-2021-0202 | 1 Juniper | 17 Ex9200, Junos, Mx10 and 14 more | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPC (Modular Port Concentrator) where Integrated Routing and Bridging (IRB) interface is configured and it is mapped to a VPLS instance or a Bridge-Domain, certain network events at Customer Edge (CE) device may cause memory leak in the MPC which can cause an out of memory and MPC restarts. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). Please refer to https://kb.juniper.net/KB25385 for the list of Trio-based PFEs. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3R3-S8; 17.4R3-S2; 18.2R3-S4, 18.2R3-S5; 18.3R3-S2, 18.3R3-S3; 18.4 versions starting from 18.4R3-S1 and later versions prior to 18.4R3-S6; 19.2 versions starting from 19.2R2 and later versions prior to 19.2R3-S1; 19.4 versions starting from 19.4R2 and later versions prior to 19.4R2-S3, 19.4R3; 20.2 versions starting from 20.2R1 and later versions prior to 20.2R1-S3, 20.2R2. This issue does not affect Juniper Networks Junos OS: 18.1, 19.1, 19.3, 20.1. | |||||
| CVE-2020-1671 | 1 Juniper | 1 Junos | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a malformed DHCPv6 packet is received, resulting with the restart of the daemon. This issue only affects DHCPv6, it does not affect DHCPv4. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.2 version 19.2R2 and later versions; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; This issue does not affect Juniper Networks Junos OS prior to 17.4R1. | |||||
| CVE-2021-0206 | 1 Juniper | 17 Junos, Nfx150, Nfx250 and 14 more | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| A NULL Pointer Dereference vulnerability in Juniper Networks Junos OS allows an attacker to send a specific packet causing the packet forwarding engine (PFE) to crash and restart, resulting in a Denial of Service (DoS). By continuously sending these specific packets, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue only affects Juniper Networks NFX Series, SRX Series platforms when SSL Proxy is configured. This issue affects Juniper Networks Junos OS on NFX Series and SRX Series: 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S1; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S2, 19.2R2; 19.3 versions prior to 19.3R2. This issue does not affect Juniper Networks Junos OS versions on NFX Series and SRX Series prior to 18.3R1. | |||||