Total
70 CVE
| CVE | Vendors | Products | Updated | CVSS v2 | CVSS v3 |
|---|---|---|---|---|---|
| CVE-2021-1229 | 1 Cisco | 86 Mds 9148s, Mds 9250i, Mds 9706 and 83 more | 2023-12-10 | 4.3 MEDIUM | 5.3 MEDIUM |
| A vulnerability in ICMP Version 6 (ICMPv6) processing in Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a slow system memory leak, which over time could lead to a denial of service (DoS) condition. This vulnerability is due to improper error handling when an IPv6-configured interface receives a specific type of ICMPv6 packet. An attacker could exploit this vulnerability by sending a sustained rate of crafted ICMPv6 packets to a local IPv6 address on a targeted device. A successful exploit could allow the attacker to cause a system memory leak in the ICMPv6 process on the device. As a result, the ICMPv6 process could run out of system memory and stop processing traffic. The device could then drop all ICMPv6 packets, causing traffic instability on the device. Restoring device functionality would require a device reboot. | |||||
| CVE-2021-1368 | 1 Cisco | 101 Firepower 4110, Firepower 4112, Firepower 4115 and 98 more | 2023-12-10 | 4.9 MEDIUM | 8.8 HIGH |
| A vulnerability in the Unidirectional Link Detection (UDLD) feature of Cisco FXOS Software and Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to execute arbitrary code with administrative privileges or cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by sending crafted Cisco UDLD protocol packets to a directly connected, affected device. A successful exploit could allow the attacker to execute arbitrary code with administrative privileges or cause the Cisco UDLD process to crash and restart multiple times, causing the affected device to reload and resulting in a DoS condition. Note: The UDLD feature is disabled by default, and the conditions to exploit this vulnerability are strict. The attacker needs full control of a directly connected device. That device must be connected over a port channel that has UDLD enabled. To trigger arbitrary code execution, both the UDLD-enabled port channel and specific system conditions must exist. In the absence of either the UDLD-enabled port channel or the system conditions, attempts to exploit this vulnerability will result in a DoS condition. It is possible, but highly unlikely, that an attacker could control the necessary conditions for exploitation. The CVSS score reflects this possibility. However, given the complexity of exploitation, Cisco has assigned a Medium Security Impact Rating (SIR) to this vulnerability. | |||||
| CVE-2021-1230 | 1 Cisco | 41 Nexus 9000v, Nexus 92160yc-x, Nexus 92300yc and 38 more | 2023-12-10 | 7.1 HIGH | 7.5 HIGH |
| A vulnerability with the Border Gateway Protocol (BGP) for Cisco Nexus 9000 Series Fabric Switches in Application Centric Infrastructure (ACI) mode could allow an unauthenticated, remote attacker to cause a routing process to crash, which could lead to a denial of service (DoS) condition. This vulnerability is due to an issue with the installation of routes upon receipt of a BGP update. An attacker could exploit this vulnerability by sending a crafted BGP update to an affected device. A successful exploit could allow the attacker to cause the routing process to crash, which could cause the device to reload. This vulnerability applies to both Internal BGP (IBGP) and External BGP (EBGP). Note: The Cisco implementation of BGP accepts incoming BGP traffic from explicitly configured peers only. To exploit this vulnerability, an attacker would need to send a specific BGP update message over an established TCP connection that appears to come from a trusted BGP peer. | |||||
| CVE-2020-3394 | 1 Cisco | 65 Nexus 3016, Nexus 3048, Nexus 3064 and 62 more | 2023-12-10 | 7.2 HIGH | 7.8 HIGH |
| A vulnerability in the Enable Secret feature of Cisco Nexus 3000 Series Switches and Cisco Nexus 9000 Series Switches in standalone NX-OS mode could allow an authenticated, local attacker to issue the enable command and get full administrative privileges. To exploit this vulnerability, the attacker would need to have valid credentials for the affected device. The vulnerability is due to a logic error in the implementation of the enable command. An attacker could exploit this vulnerability by logging in to the device and issuing the enable command. A successful exploit could allow the attacker to gain full administrative privileges without using the enable password. Note: The Enable Secret feature is disabled by default. | |||||
| CVE-2020-3454 | 1 Cisco | 83 Mds 9000, Mds 9100, Mds 9134 and 80 more | 2023-12-10 | 9.0 HIGH | 7.2 HIGH |
| A vulnerability in the Call Home feature of Cisco NX-OS Software could allow an authenticated, remote attacker to inject arbitrary commands that could be executed with root privileges on the underlying operating system (OS). The vulnerability is due to insufficient input validation of specific Call Home configuration parameters when the software is configured for transport method HTTP. An attacker could exploit this vulnerability by modifying parameters within the Call Home configuration on an affected device. A successful exploit could allow the attacker to execute arbitrary commands with root privileges on the underlying OS. | |||||
| CVE-2020-3415 | 1 Cisco | 66 Nexus 3016, Nexus 3048, Nexus 3064 and 63 more | 2023-12-10 | 7.9 HIGH | 8.8 HIGH |
| A vulnerability in the Data Management Engine (DME) of Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to execute arbitrary code with administrative privileges or cause a denial of service (DoS) condition on an affected device. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by sending a crafted Cisco Discovery Protocol packet to a Layer 2-adjacent affected device. A successful exploit could allow the attacker to execute arbitrary code with administrative privileges or cause the Cisco Discovery Protocol process to crash and restart multiple times, causing the affected device to reload and resulting in a DoS condition. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). Exploitation of this vulnerability also requires jumbo frames to be enabled on the interface that receives the crafted Cisco Discovery Protocol packets on the affected device. | |||||
| CVE-2020-3397 | 1 Cisco | 64 Nexus 3016, Nexus 3048, Nexus 3064 and 61 more | 2023-12-10 | 7.1 HIGH | 8.6 HIGH |
| A vulnerability in the Border Gateway Protocol (BGP) Multicast VPN (MVPN) implementation of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause an affected device to unexpectedly reload, resulting in a denial of service (DoS) condition. The vulnerability is due to incomplete input validation of a specific type of BGP MVPN update message. An attacker could exploit this vulnerability by sending this specific, valid BGP MVPN update message to a targeted device. A successful exploit could allow the attacker to cause one of the BGP-related routing applications to restart multiple times, leading to a system-level restart. Note: The Cisco implementation of BGP accepts incoming BGP traffic from only explicitly configured peers. To exploit this vulnerability, an attacker must send a specific BGP MVPN update message over an established TCP connection that appears to come from a trusted BGP peer. To do so, the attacker must obtain information about the BGP peers in the trusted network of the affected system. | |||||
| CVE-2020-3338 | 1 Cisco | 67 Nexus 3016, Nexus 3048, Nexus 3064 and 64 more | 2023-12-10 | 5.0 MEDIUM | 7.5 HIGH |
| A vulnerability in the Protocol Independent Multicast (PIM) feature for IPv6 networks (PIM6) of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper error handling when processing inbound PIM6 packets. An attacker could exploit this vulnerability by sending multiple crafted PIM6 packets to an affected device. A successful exploit could allow the attacker to cause the PIM6 application to leak system memory. Over time, this memory leak could cause the PIM6 application to stop processing legitimate PIM6 traffic, leading to a DoS condition on the affected device. | |||||
| CVE-2020-3504 | 1 Cisco | 108 Firepower 1010, Firepower 1120, Firepower 1140 and 105 more | 2023-12-10 | 2.1 LOW | 3.3 LOW |
| A vulnerability in the local management (local-mgmt) CLI of Cisco UCS Manager Software could allow an authenticated, local attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to improper handling of CLI command parameters. An attacker could exploit this vulnerability by executing specific commands on the local-mgmt CLI on an affected device. A successful exploit could allow the attacker to cause internal system processes to fail to terminate properly, which could result in a buildup of stuck processes and lead to slowness in accessing the UCS Manager CLI and web UI. A sustained attack may result in a restart of internal UCS Manager processes and a temporary loss of access to the UCS Manager CLI and web UI. | |||||
| CVE-2020-3517 | 1 Cisco | 98 Firepower 4110, Firepower 4112, Firepower 4115 and 95 more | 2023-12-10 | 7.8 HIGH | 8.6 HIGH |
| A vulnerability in the Cisco Fabric Services component of Cisco FXOS Software and Cisco NX-OS Software could allow an unauthenticated attacker to cause process crashes, which could result in a denial of service (DoS) condition on an affected device. The attack vector is configuration dependent and could be remote or adjacent. For more information about the attack vector, see the Details section of this advisory. The vulnerability is due to insufficient error handling when the affected software parses Cisco Fabric Services messages. An attacker could exploit this vulnerability by sending malicious Cisco Fabric Services messages to an affected device. A successful exploit could allow the attacker to cause a reload of an affected device, which could result in a DoS condition. | |||||
| CVE-2020-3398 | 1 Cisco | 67 Nexus 3016, Nexus 3048, Nexus 3064 and 64 more | 2023-12-10 | 4.3 MEDIUM | 8.6 HIGH |
| A vulnerability in the Border Gateway Protocol (BGP) Multicast VPN (MVPN) implementation of Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause a BGP session to repeatedly reset, causing a partial denial of service (DoS) condition due to the BGP session being down. The vulnerability is due to incorrect parsing of a specific type of BGP MVPN update message. An attacker could exploit this vulnerability by sending this BGP MVPN update message to a targeted device. A successful exploit could allow the attacker to cause the BGP peer connections to reset, which could lead to BGP route instability and impact traffic. The incoming BGP MVPN update message is valid but is parsed incorrectly by the NX-OS device, which could send a corrupted BGP update to the configured BGP peer. Note: The Cisco implementation of BGP accepts incoming BGP traffic from only explicitly configured peers. To exploit this vulnerability, an attacker must send a specific BGP MVPN update message over an established TCP connection that appears to come from a trusted BGP peer. To do so, the attacker must obtain information about the BGP peers in the trusted network of the affected system. | |||||
| CVE-2019-12662 | 1 Cisco | 135 Ios Xe, Mds 9000, Nexus 3016 and 132 more | 2023-12-10 | 7.2 HIGH | 6.7 MEDIUM |
| A vulnerability in Cisco NX-OS Software and Cisco IOS XE Software could allow an authenticated, local attacker with valid administrator or privilege level 15 credentials to load a virtual service image and bypass signature verification on an affected device. The vulnerability is due to improper signature verification during the installation of an Open Virtual Appliance (OVA) image. An authenticated, local attacker could exploit this vulnerability and load a malicious, unsigned OVA image on an affected device. A successful exploit could allow an attacker to perform code execution on a crafted software OVA image. | |||||
| CVE-2019-1734 | 1 Cisco | 94 Firepower 4110, Firepower 4112, Firepower 4115 and 91 more | 2023-12-10 | 2.1 LOW | 5.5 MEDIUM |
| A vulnerability in the implementation of a CLI diagnostic command in Cisco FXOS Software and Cisco NX-OS Software could allow an authenticated, local attacker to view sensitive system files that should be restricted. The attacker could use this information to conduct additional reconnaissance attacks. The vulnerability is due to incomplete role-based access control (RBAC) verification. An attacker could exploit this vulnerability by authenticating to the device and issuing a specific CLI diagnostic command with crafted user-input parameters. An exploit could allow the attacker to perform an arbitrary read of a file on the device, and the file may contain sensitive information. The attacker needs valid device credentials to exploit this vulnerability. | |||||
| CVE-2020-3165 | 1 Cisco | 65 Nexus 3016, Nexus 3048, Nexus 3064 and 62 more | 2023-12-10 | 4.3 MEDIUM | 8.2 HIGH |
| A vulnerability in the implementation of Border Gateway Protocol (BGP) Message Digest 5 (MD5) authentication in Cisco NX-OS Software could allow an unauthenticated, remote attacker to bypass MD5 authentication and establish a BGP connection with the device. The vulnerability occurs because the BGP MD5 authentication is bypassed if the peer does not have MD5 authentication configured, the NX-OS device does have BGP MD5 authentication configured, and the NX-OS BGP virtual routing and forwarding (VRF) name is configured to be greater than 19 characters. An attacker could exploit this vulnerability by attempting to establish a BGP session with the NX-OS peer. A successful exploit could allow the attacker to establish a BGP session with the NX-OS device without MD5 authentication. The Cisco implementation of the BGP protocol accepts incoming BGP traffic only from explicitly configured peers. To exploit this vulnerability, an attacker must send the malicious packets over a TCP connection that appears to come from a trusted BGP peer. To do so, the attacker must obtain information about the BGP peers in the affected system’s trusted network. | |||||
| CVE-2020-3119 | 1 Cisco | 83 Nexus 3016, Nexus 3048, Nexus 3064 and 80 more | 2023-12-10 | 8.3 HIGH | 8.8 HIGH |
| A vulnerability in the Cisco Discovery Protocol implementation for Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to execute arbitrary code or cause a reload on an affected device. The vulnerability exists because the Cisco Discovery Protocol parser does not properly validate input for certain fields in a Cisco Discovery Protocol message. An attacker could exploit this vulnerability by sending a malicious Cisco Discovery Protocol packet to an affected device. An successful exploit could allow the attacker to cause a stack overflow, which could allow the attacker to execute arbitrary code with administrative privileges on an affected device. Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). | |||||
| CVE-2020-3174 | 1 Cisco | 80 Mds 9132t, Mds 9148s, Mds 9148t and 77 more | 2023-12-10 | 3.3 LOW | 4.7 MEDIUM |
| A vulnerability in the anycast gateway feature of Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a device to learn invalid Address Resolution Protocol (ARP) entries. The ARP entries are for nonlocal IP addresses for the subnet. The vulnerability is due to improper validation of a received gratuitous ARP (GARP) request. An attacker could exploit this vulnerability by sending a malicious GARP packet on the local subnet to cause the ARP table on the device to become corrupted. A successful exploit could allow the attacker to populate the ARP table with incorrect entries, which could lead to traffic disruptions. | |||||
| CVE-2019-12717 | 1 Cisco | 88 Nexus 3016, Nexus 3048, Nexus 3064 and 85 more | 2023-12-10 | 7.2 HIGH | 7.8 HIGH |
| A vulnerability in a CLI command related to the virtualization manager (VMAN) in Cisco NX-OS Software could allow an authenticated, local attacker to execute arbitrary commands on the underlying Linux operating system with root privileges. The vulnerability is due to insufficient validation of arguments passed to a specific VMAN CLI command on an affected device. An attacker could exploit this vulnerability by including malicious input as the argument of an affected command. A successful exploit could allow the attacker to execute arbitrary commands on the underlying Linux operating system with root privileges, which may lead to complete system compromise. An attacker would need valid administrator credentials to exploit this vulnerability. | |||||
| CVE-2020-3120 | 1 Cisco | 144 Asr 9000v, Asr 9001, Asr 9006 and 141 more | 2023-12-10 | 6.1 MEDIUM | 6.5 MEDIUM |
| A vulnerability in the Cisco Discovery Protocol implementation for Cisco FXOS Software, Cisco IOS XR Software, and Cisco NX-OS Software could allow an unauthenticated, adjacent attacker to cause a reload of an affected device, resulting in a denial of service (DoS) condition. The vulnerability is due to a missing check when the affected software processes Cisco Discovery Protocol messages. An attacker could exploit this vulnerability by sending a malicious Cisco Discovery Protocol packet to an affected device. A successful exploit could allow the attacker to exhaust system memory, causing the device to reload. Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent). | |||||
| CVE-2019-1590 | 1 Cisco | 28 Nexus 9000, Nexus 92160yc-x, Nexus 92300yc and 25 more | 2023-12-10 | 6.8 MEDIUM | 8.1 HIGH |
| A vulnerability in the Transport Layer Security (TLS) certificate validation functionality of Cisco Nexus 9000 Series Application Centric Infrastructure (ACI) Mode Switch Software could allow an unauthenticated, remote attacker to perform insecure TLS client authentication on an affected device. The vulnerability is due to insufficient TLS client certificate validations for certificates sent between the various components of an ACI fabric. An attacker who has possession of a certificate that is trusted by the Cisco Manufacturing CA and the corresponding private key could exploit this vulnerability by presenting a valid certificate while attempting to connect to the targeted device. An exploit could allow the attacker to gain full control of all other components within the ACI fabric of an affected device. | |||||
| CVE-2019-1776 | 1 Cisco | 134 7000 10-slot, 7000 18-slot, 7000 4-slot and 131 more | 2023-12-10 | 7.2 HIGH | 6.7 MEDIUM |
| A vulnerability in the CLI of Cisco NX-OS Software could allow an authenticated, local attacker to execute arbitrary commands on the underlying Linux operating system with a privilege level of root. The vulnerability is due to insufficient validation of arguments passed to a specific CLI command on the affected device. An attacker could exploit this vulnerability by including malicious input as the argument of an affected command. A successful exploit could allow the attacker to execute arbitrary commands on the underlying Linux operating system with elevated privileges. An attacker would need valid administrator credentials to exploit this vulnerability. | |||||